INDIVIDUAL JET PUMP PARTS

 

We carry a variety of performance jet boat parts and pumps, marine engine parts, and marine exhaust systems and silencers, including all the rebuild parts like jet pump shafts and packings, gaskets, and wear rings. Take advantage of our experience and knowledge and contact us today for all your needs.

    Pump Shaft
    		 High Performance Jet Pump Shaft
    This is a 17-4 Jet pump shaft, Known to be the strongest in the industry. A must for any Weekend warrior or your all out Blown Alcohol Jet boat!
    #AG 2020 17-4 Shaft
    Shaft End Repair Sleeve Shaft End (Repair Sleeve)
    No need to replace the entire shaft because of damage due to Sand or lack of maintenance, this repair sleeve allows you to Repair the end of the shaft. “Requires Machining”
    #AG 31309
    Shaft Sleeve Slinger Ring Shaft Sleeve (Slinger Ring)
    Available for: American turbine, Berkeley & Dominator. Must specify make of pump and serial # when ordering
    #AKS 111
      Pump Shaft Packing
    		Pump Shaft (Packing)
    DPS packing seal cartridge unit
    Increase Shaft H.P. & Eliminate cavitations caused by a loose packing
    #DPS 1353
     
    Standard Rope seal packing (Woven graphite)
    # ARS 8287
    Thrust Bearing Thrust Bearing
    This is a Double Row 8 balls per row 16 total. Good for use on moderate applications up to 500 H.P
    Thrust Bearing Extreme Duty Thrust Bearing
    This is an Extreme duty, 11 ball double row angular contact bearing. Used in High Horsepower applications where severe axial thrust loads are present. "Filling slot faces motor" "Care must be taken when installing bearing onto shaft,Only press on inner race of bearing"
    Bronze Shouldered Wear Ring Bronze Shouldered (Wear rings)
    Create a double seal with these shouldered wear rings
    Available for: American turbine, Berkeley & Dominator.
    Over sizes available to fit you’re used impeller
    Must specify Impeller wear ring surface Length & Diameter
    Make of Pump and Serial # when ordering.
    #AKS WR5000
     

    STOCK Berkeley NON shoulderd wear ring Stainless Steel
    These are the STOCK non shoulderd wear rings that come in a Berkeley pump. Made of Stainless Steel!

    Plastic Insulator Plastic (Insulator)
    Designed to effectively hold the wear ring in place.
    #AT WR6004
    Impeller Shim Impeller (Shims)
    Impeller shim Kit
    #AG 130XX
    Impeller Nut Impeller (Nut)
    Billet Machined
    #AG 2035
    Impeller Key Impeller (Key)
    1/4” Stainless steel Key
    #AG 2031
    Seals for Bearing Cap, Suction Housing, and Bowl

    Seals (Bearing Cap)
    Driveshaft or bearing cap seal
    #ARS 31237

    Seals (Suction Housing)
    Slinger ring seal “Specify make of pump & serial #”
    #AKS 31252

    Seals (Bowl)
    Bowl seal
    #ARS 31239

     

    Berkeley Bowl Glacier bearings pair
    Berkeley Bowl Glacier Bearings.

     

    Dominator Bowl Glacier bearings, pair
    Used in Dominator bowls.

    Pin Bushing (Nyliner)
    Pin Bushings (Nyliners)
    Pin sizes 3/8” or 1/2”
    #ARS 31240 3/8”
    #ARS 31234 1/2”
    Gasket Sealant
    4 oz. Gasket Sealing Compound
    Gaskets
    Gaskets
    #ARS 31285 Intake / Suction
    #ARS 31247 Bearing cap 4 hole
    #ARS 31248 Bearing cap 8 hole
    #ARS 31235 Bowl 8 Hole
    #ARS 31236 Bowl 16 Hole (Double Drilled)
    #ARS 31265 Nozzle Housing 8 hole
    #ARS 31266 Nozzle Housing 16 hole (Double Drilled)
    #ARS 31242 Transom Housing Rubber

 

home page | about us | services | ARS parts | shop online | on sale | contact us | links | gallery